Drying tanks

DT hot-air drying tanks

Hot-air drying tanks of 96 to 300 L (25.4 to 79.3 US gal) for the ST cleaners; the DT-96 and DT-206 take the ST-96 and ST-206 basket without repacking.

Discuss your processSpecifications

DT hot-air drying tanks
DT-206 — front view

About this series

The DT series dries what the cleaner has just washed. A heating turbine moves hot air through the load, so water is off the part before it can flash-rust or carry spots into assembly. The DT-96 and DT-206 match the ST-96 and ST-206, so their basket comes out of the cleaner and goes straight into the dryer without being repacked; the DT-300 takes baskets up to 820 × 520 mm (32.3 × 20.5 in).

The lid is diamond-shaped so condensate runs off rather than dripping back, it is hinged and integrated, the basket is reinforced stainless steel, and a digital timer and thermostat sit in the control cabinet.

Discuss your process

DT hot-air drying tanks

How the DT dries

A hot-air drying tank for the end of the wash and rinse: a heating turbine drives warm air through the basket, so parts leave dry, without water spots or flash rust. Three sizes, 96 L (25.4 US gal), 206 L (54.4 US gal) and 300 L (79.3 US gal), matched to the ST wash tanks.

Select a function for the details.

DT hot-air drying tanks

Heating turbine, forced hot air

A heating turbine drives a high volume of hot air through the chamber for fast, even drying of the whole basket.

The blower moves heated air through the insulated chamber with an even circulation, so complex and multi-layered parts dry as well as simple ones. It is built for low-noise running.

Hot air dries without touching the parts: no cloths and no risk of mechanical damage to delicate components. HEPA-filtered inlet air is available as an option.

Read more in the knowledge base

DT hot-air drying tanks

Air up to 100 °C (212 °F)

The air temperature is adjustable up to 100 °C (212 °F), so heat-sensitive metals and coatings can be dried at a lower setting.

On the DT-96 and DT-206 the air is set room temperature to 100 °C (212 °F), with heaters of 3 kW and 6 kW. On the DT-300 the air goes up to 100 °C (212 °F); heater rating on request.

Choose a lower setting for heat-sensitive metals and coatings, and a higher one where the parts tolerate it and the cycle should be short.

Read more in the knowledge base

DT hot-air drying tanks

Digital timer and thermostat

A digital timer and a digital thermostat in the control cabinet set the drying time and the air temperature.

Set the time to the heat capacity of the load: a heavy batch of metal parts needs longer to warm up and dry than a light one. The timer ends the cycle on its own, and the same settings give the same result batch after batch.

DT hot-air drying tanks

Matched to the ST-96 and ST-206

The DT-96 and DT-206 match the ST-96 and ST-206, so their basket goes from the washer into the dryer without being repacked. The DT-300 takes baskets up to 820 × 520 mm (32.3 × 20.5 in).

The inside dimensions are 600 × 400 × 400 mm (23.6 × 15.7 × 15.7 in) on the DT-96, 750 × 550 × 500 mm (29.5 × 21.7 × 19.7 in) on the DT-206 and 900 × 600 × 560 mm (35.4 × 23.6 × 22.0 in) on the DT-300.

In a wash, rinse and dry sequence the DT stands at the end: the water comes off before it can leave spots or start flash rust, and the parts go to assembly, inspection or packaging straight away.

Read more in the knowledge base

DT hot-air drying tanks

Diamond-profile lid

The hinged, integrated lid has a diamond-shaped profile: condensate runs off instead of dripping back onto the parts.

Moist air from the wet parts condenses on the underside of the lid. On a flat lid it would drip back onto the dried parts; the diamond profile lets it run off.

The lid is hinged to the tank, so it stays with the machine and keeps the heat in the chamber during the cycle.

DT hot-air drying tanks

Reinforced stainless basket

A reinforced stainless steel basket carries 100 kg (220 lb) on the DT-96 and DT-206 and 125 kg (276 lb) on the DT-300.

The basket measures 580 × 380 × 200 mm (22.8 × 15.0 × 7.9 in) on the DT-96 and 730 × 530 × 260 mm (28.7 × 20.9 × 10.2 in) on the DT-206.

The volume lets heavier parts or several items dry in one cycle; multi-tier shelving is available as an option to spread the load over several levels.

Read more in the knowledge base

DT hot-air drying tanks

Insulated stainless chamber

An insulated chamber in AISI304 stainless steel from 2 mm (0.08 in) thick, on lockable castor wheels.

The insulation keeps the heat in the chamber, where the parts are. Stainless steel stands up to warm, humid air and suits clean working areas.

Lockable castor wheels let the dryer be moved into place beside the wash and rinse tanks and fixed there. All three sizes run on a 400 V supply.

For US sites the DT dryers are quoted for 480 V or 208–240 V three-phase, 60 Hz, with 60 Hz motors.

Read more in the knowledge base

DT hot-air drying tanks

Drying after rinsing

Parts leave dry for the next step, with less hand drying. Spots and flash rust depend on rinse water and drying time; we set both with you in a trial.

Water left on a cleaned part dries into spots and, on steel, starts corrosion and oxidation. Drying straight after the rinse removes the moisture from every surface.

Hand drying ties up staff; the dryer frees them for other work. Typical uses: machined and precision parts, PCBs and electronic housings, medical and laboratory tools and trays after washing, watch and jewellery parts, brake components and valves.

Read more in the knowledge base

DT options

Available on request — ask for a quote.

Double blower and air knives

Two blowers with air knives inside the tank blow cups, caps and complex parts dry quickly. This configuration has been built for a closure and cap manufacturer. Discuss your parts and drying process with us for a quote.

HEPA filtration of drying air

HEPA filtration of the drying air is available on request for clean or sensitive parts. Tell us your cleanliness requirements so we can quote the appropriate configuration.

Request a quote ↗

Models

Every size in this series.

DT hot-air drying tanks

Specifications

DT-96DT-206DT-300
Nominal volume*96 L (25.4 US gal)206 L (54.4 US gal)300 L (79.3 US gal)
Tank size600 × 400 × 400 mm (23.6 × 15.7 × 15.7 in)750 × 550 × 500 mm (29.5 × 21.7 × 19.7 in)900 × 600 × 560 mm (35.4 × 23.6 × 22.0 in)
Useful tank size600 × 400 × 400 mm (23.6 × 15.7 × 15.7 in)750 × 550 × 500 mm (29.5 × 21.7 × 19.7 in)820 × 520 × 540 mm (32.3 × 20.5 × 21.3 in)
Machine size1050 × 780 × 1050 mm (41.3 × 30.7 × 41.3 in)1230 × 940 × 1200 mm (48.4 × 37.0 × 47.2 in)1250 × 900 × 1200 mm (49.2 × 35.4 × 47.2 in)
Basket size580 × 380 × 200 mm (22.8 × 15.0 × 7.9 in)730 × 530 × 260 mm (28.7 × 20.9 × 10.2 in)—
Load capacity100 kg (220 lb)100 kg (220 lb)125 kg (276 lb)
Heating power3000 W6000 W—
TimerDigitalDigital—
Temperature rangeroom temperature to 100 °C (212 °F)room temperature to 100 °C (212 °F)room temperature to 100 °C (212 °F)
Power supply400 V/16 A400 V/16 A400 V

US versions on request: 480 V or 208–240 V three-phase, 60 Hz, with 60 Hz motors; current and plug are confirmed in the quote (DT-300 engineered per order).

* Nominal volume: calculated from the inner tank dimensions (length × width × height). Rounded corners, the tank's construction and the maximum fill line mean the amount of liquid in use is lower.

Custom machines

Not in the standard range? We build it.

Every industrial machine is made to order, so the tank size, material, heating, filtration, lid, lift and controls follow your parts and your process. If the machine you need is not on this page, describe the parts and the soil and we design it around them.

In a production setting

DT-206 shown in a factory setting. Image composed from our studio photo.

Let's find the right fit

Not sure which size you need?

Send us the part, the quantity per hour and the soil you are removing. We will size the tank and the frequency with you.

Discuss your process

Region

Choose your country or region

Sonixtek quotes and supplies directly through its regional companies. Your choice sets the contact details shown on the site and which Sonixtek company handles your enquiry.